Видео

Good stuff Joe. Locking off and proving dead or not live should be drummed in until it is second nature like doing up your showlaces. It should also be one of the first tools an Apprentice gets in their toolbox.

There is all types that will fit now 👌👍

Lots of cable for when extending.

So how come Wickes sell 2m lengths? Is it the same as their shite quality timber? 😂

I was taught in college to test each wire of the live to mcb and just clamp.it to the neutral bar without a strapper then the earth to neutral and then the earth to live. What's the difference now ? Is it because of split boards?

The guy we bought our house from had hot wires everywhere . All safe now but one job he did he used foil and Christmas tree light wire

Or simply use a wall chaser

landlords getting some tips with this one

ruclips.net/video/kMJPmDRkduU/видео.htmlsi=qo3S1oE2cg97Xnq0

That lock ain't stopping no one 💀

Well, actually it is "allowed" but flex is more expensive than Class 1 T&CPC so why bother when it doesn't need to be flexible? A right mess though!

pointless doubling over when there are 2 cables going into the socket.

So I have the first switch fused, all electrics works as should but when I switch off at fuse electrics still work, even when I take fuse out!

was the container bonded?

Painful watching you strip that

That's like the old wizards sleeve trick😂

😮😮😮😮

Show how to measure insulation and RCD.

One line conduction rnot terminated in the middle lampholder ?

I'm not a qualified sparkie, but even I know that is wrong on so many levels! Lucky that didn't cause a fire!

You got the shakes in this vid? A good point for any apprentice, beginner. Do not cut and expel copper wire over a socket like he has. Fast way to cause a short.

Brill explaination

Great instructional, thanks Gaz

Jabardast wiring hai 😊😊😊

Sir it's not poison its power

All your videos are very well explained, are very helpful. Thanks a lot Sir.

😮

They have given plenty of slack incase they need to move its location maybe

I am a bit confused as a new student bit at the end of the test in front of the white board with Marcus, you made the note as r2 1.67 i thought that was spouse to be cpc end to end reading why did u put there 1.67 as r2? thanx

If I seen this I would suspect there is lots more amateur wiring to be found

Just use stripers like normal electricians do! And why double the ends? Single I can understand but doubles?

On a tncs couldnt you use earth as a neutral?

"just leave a bit of slack" the apprentice:

And I suspect that twin at the back of the box fed the cabinet lights.

2 words: Kitchen fitters.

Many thanks for explaining and making this switch wiring so simple, I needed to replace my old worn switch but didn't understand the wiring, now I know, cheers

Quality work 👏

I cant understand what you are using to bend it how does that tool called

Great video guys thanks . Is this a MSB or a sub board? Is there a MEN link in the board? Also when disconnecting the 16mm main earth cable, would that be the one from the earth stake or up stream supply? Im assuming this is a sub board? Question from Down under AUZ where we use TNCS MEN system. cheers for showing me how to use my megger properly. Legends

Why float the Neutral just have the wire in both ends not terminated.

If I mark the copper slightly (only slight grazing) will that affect the resistance of the circuit?

Brilliant instructions so easy to understand, thanks to the Tutor 100% and YES it works

This may be a stupid question but do you find which is the live feed by testing with a phase tester ????

Concise clear and well explained 👍🏻

Can the Lamps share the same neutral circuit as the PIR's?

Need some help, i have 1 gang 2 way switches. (Switch 1) black wire brown sleeve into L1, brown wire into L2 and grey wire brown sleeve into L3 (Switch 2) black wire brown sleeve into L1, 2 brown wires into L2, grey with brown sleeve+blue wires L3 2 earth wires go into connect box. I want to change one switch with a dimmer switch ( BG electrical evolve single touch 2 way master) at the rear there are 3 connections. 1) wavy line with arrow through it. 2) s.link. 3) L Does black wire brown sleeve go into wavy line with arrow , brown wires go into L, and grey with brown sleeve+ blue wire into s.link ? I would really appreciate your help 👍